|
|
REFERENCES: FAA-H-8083-3; FAA-S-8081-12, FAA-S-8081-14; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of maneuvering during slow flight by describing-
a. relationship of configuration, weight, center of gravity, maneuvering loads, angle of bank, and power to flight characteristics and controllability.
b. relationship of the maneuver to critical flight situations, such as go-around.
c. performance of the maneuver with selected landing gear and flap configurations in straight-and-level flight and level turns.
d. specified airspeed for the maneuver.
e. coordination of flight controls.
f. trim technique.
g. reestablishment of cruise flight.
2. Exhibits instructional knowledge of common errors related to maneuvering during slow flight by describing-
a. failure to establish specified gear and flap configuration.
b. improper entry technique.
c. failure to establish and maintain the specified airspeed.
d. excessive variations of altitude and heading when a constant altitude and heading are specified.
e. rough or uncoordinated control technique.
f. improper correction for torque effect.
g. improper trim technique.
h. unintentional stalls.
i. inappropriate removal of hand from throttles.
3. Demonstrates and simultaneously explains maneuvering during slow flight from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to maneuvering during slow flight.
|
|
|
|
|
REFERENCES: AC 61-67; FAA-H-8083-3; FAA-S-8081-12, FAA-S-8081-14; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of power-on stalls, in climbing flight (straight or turning), with selected landing gear and flap configurations by describing-
a. aerodynamics of power-on stalls.
b. relationship of various factors such as landing gear and flap configuration, weight, center of gravity, load factor, and bank angle to stall speed.
c. flight situations where unintentional power-on stalls may occur.
d. entry technique and minimum entry altitude.
e. performance of power-on stalls in climbing flight (straight or turning).
f. coordination of flight controls.
g. recognition of the first indications of power-on stalls.
h. recovery technique and minimum recovery altitude.
2. Exhibits instructional knowledge of common errors related to power-on stalls, in climbing flight (straight or turning), with selected landing gear and flap configurations by describing-
a. failure to establish the specified landing gear and flap configuration prior to entry.
b. improper pitch, heading, and bank control during straight ahead and turning stalls.
c. improper pitch and bank control during turning stalls.
d. rough or uncoordinated control procedure.
e. failure to recognize the first indications of a stall.
f. failure to achieve a stall.
g. improper torque correction.
h. poor stall recognition and delayed recovery.
i. excessive altitude loss or excessive airspeed during recovery.
j. secondary stall during recovery.
3. Demonstrates and simultaneously explains power-on stalls, in climbing flight (straight or turning), with selected landing gear and flap configurations, from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to power-on stalls, in climbing flight (straight or turning), with selected landing gear and flap configurations.
|
|
|
|
|
REFERENCES: FAA-H-8083-3; FAA-S-8081-12, FAA-S-8081-14; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of power-off stalls, in descending flight (straight or turning), with selected landing gear and flap configurations by describing-
a. aerodynamics of power-off stalls.
b. relationship of various factors, such as landing gear and flap configuration, weight, center of gravity, load factor, and bank angle to stall speed.
c. flight situations where unintentional power-off stalls may occur.
d. entry technique and minimum entry altitude.
e. performance of power-off stalls in descending flight (straight or turning).
f. coordination of flight controls.
g. recognition of the first indications of power-off stalls.
h. recovery technique and minimum recovery altitude.
2. Exhibits instructional knowledge of common errors related to power-off stalls, in descending flight (straight or turning), with selected landing gear and flap configurations by describing-
a. failure to establish the specified landing gear and flap configuration prior to entry.
b. improper pitch, heading, and bank control during straight-ahead stalls.
c. improper pitch and bank control during turning stalls.
d. rough or uncoordinated control technique.
e. failure to recognize the first indications of a stall.
f. failure to achieve a stall.
g. improper torque correction.
h. poor stall recognition and delayed recovery.
i. excessive altitude loss or excessive airspeed during recovery.
j. secondary stall during recovery.
3. Demonstrates and simultaneously explains power-off stalls, in descending flight (straight or turning), with selected landing gear and flap configurations, from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to power-off stalls, in descending flight (straight or turning), with selected landing gear and flap configurations.
|
|
|
|
|
REFERENCES: FAA-H-8083-3; FAA-S-8081-12, FAA-S-8081-14; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of crossed-control stalls, with the landing gear extended by describing-
a. aerodynamics of crossed-control stalls.
b. effects of crossed controls in gliding or reduced airspeed descending turns.
c. flight situations where unintentional crossed-control stalls may occur.
d. entry procedure and minimum entry altitude.
e. recognition of crossed-control stalls.
f. recovery procedure and minimum recovery altitude.
2. Exhibits instructional knowledge of common errors related to crossed-control stalls, with the landing gear extended by describing-
a. failure to establish selected configuration prior to entry.
b. failure to establish a crossed-control turn and stall condition that will adequately demonstrate the hazards of a crossed-control stall.
c. improper or inadequate demonstration of the recognition and recovery from a cross-control stall.
d. failure to present simulated student instruction that emphasizes the hazards of a cross-control condition in a gliding or reduced airspeed condition.
3. Demonstrates and simultaneously explains a crossed-control stall, with the landing gear extended, from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to a crossed-control stall with the landing gear extended.
|
|
|
|
|
REFERENCES: FAA-H-8083-3; FAA-S-8081-12, FAA-S-8081-14; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of elevator trim stalls, in selected landing gear and flap configurations by describing-
a. aerodynamics of elevator trim stalls.
b. hazards of inadequate control pressures to compensate for thrust, torque, and up-elevator trim during go-around and other related maneuvers.
c. entry procedure and minimum entry altitude.
d. recognition of elevator trim stalls.
e. importance of recovering from an elevator trim stall immediately upon recognition.
2. Exhibits instructional knowledge of common errors related to elevator trim stalls, in selected landing gear and flap configurations by describing-
a. failure to present simulated student instruction that adequately emphasizes the hazards of poor correction for torque and up-elevator trim during go-around and other maneuvers.
b. failure to establish selected configuration prior to entry.
c. improper or inadequate demonstration of the recognition of and the recovery from an elevator trim stall.
3. Demonstrates and simultaneously explains elevator trim stalls, in selected landing gear and flap configurations, from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to elevator trim stalls in selected landing gear and flap configurations.
|
|
|
|
|
REFERENCES: FAA-H-8083-3; FAA-S-8081-12, FAA-S-8081-14; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of secondary stalls, in selected landing gear and flap configurations by describing-
a. aerodynamics of secondary stalls.
b. flight situations where secondary stalls may occur.
c. hazards of secondary stalls during normal stall or spin recovery.
d. entry procedure and minimum entry altitude.
e. recognition of a secondary stall.
f. recovery procedure and minimum recovery altitude.
2. Exhibits instructional knowledge of common errors related to secondary stalls, in selected landing gear and flap configurations by describing-
a. failure to establish selected configuration prior to entry.
b. improper or inadequate demonstration of the recognition of and recovery from a secondary stall.
c. failure to present simulated student instruction that adequately emphasizes the hazards of poor procedure in recovering from a primary stall.
3. Demonstrates and simultaneously explains secondary stalls, in selected landing gear and flap configurations, from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to secondary stalls in selected landing gear and flap configurations.
|
|
|
|
|
NOTE: At the discretion of the examiner, a logbook record attesting applicant instructional competency in spin entries, spins, and spin recoveries may be accepted in lieu of this TASK. The flight instructor who conducted the spin instruction must certify the logbook record.
REFERENCES: 14 CFR part 23; Type Certificate Data Sheet; AC 61-67, FAA-H-8083-3; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of spins by describing-
a. anxiety factors associated with spin instruction.
b. aerodynamics of spins.
c. airplanes approved for the spin maneuver based on airworthiness category and type certificate.
d. relationship of various factors such as configuration, weight, center of gravity, and control coordination to spins.
e. flight situations where unintentional spins may occur.
f. how to recognize and recover from imminent, unintentional spins.
g. entry procedure and minimum entry altitude for intentional spins.
h. control procedure to maintain a stabilized spin.
i. orientation during a spin.
j. recovery procedure and minimum recovery altitude for intentional spins.
2. Exhibits instructional knowledge of common errors related to spins by describing-
a. failure to establish proper configuration prior to spin entry.
b. failure to achieve and maintain a full stall during spin entry.
c. failure to close throttle when a spin entry is achieved.
d. failure to recognize the indications of an imminent, unintentional spin.
e. improper use of flight controls during spin entry, rotation, or recovery.
f. disorientation during a spin.
g. failure to distinguish between a high-speed spiral and a spin.
h. excessive speed or accelerated stall during recovery.
i. failure to recover with minimum loss of altitude.
j. hazards of attempting to spin an airplane not approved for spins.
3. Demonstrates and simultaneously explains a spin (one turn) from an instructional standpoint.
4. Analyzes and corrects simulated common errors related to spins.
|
|
|
|
|
NOTE: This TASK must be completed by oral examination or demonstration at the discretion of the examiner.
REFERENCES: FAA-H-8083-3; POH/AFM.
Objective. To determine that the applicant:
1. Exhibits instructional knowledge of the elements of accelerated maneuver stalls by describing-
a. aerodynamics of accelerated maneuver stalls.
b. flight situations where accelerated maneuver stalls may occur.
c. hazards of accelerated stalls during stall or spin recovery.
d. entry procedure and minimum entry altitude.
e. recognition of the accelerated stall.
f. recovery procedure and minimum recovery altitude.
2. Demonstrates and simultaneously explains accelerated maneuver stall, from an instructional standpoint.
3. Exhibits instructional knowledge of common errors related to accelerated maneuver stalls by describing-
a. failure to establish proper configuration prior to entry.
b. improper or inadequate demonstration of the recognition of and recovery from an accelerated maneuver stall.
c. failure to present simulated student instruction that adequately emphasizes the hazards of poor procedures in recovering from an accelerated stall.
4. Analyzes and corrects simulated common errors related to accelerated stalls.
|
|
